All codes (4.787)

• 3096 PWRCTRL DUTY activated in another channel. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3097 PWRCTRL OUT activated in another channel. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3098 PWRCTRL DUTY requires active PWM in the same channel. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3099 LEAP not activated due to jump height below a minimum. CNCelite 8058 / 8060 / 8065 / 8070
• 3099 LEAP not activated due to jump height below a minimum. CNC 8058 / 8060 / 8065 · CNC 8070
• 3100 Excessive power on the spindle detected during DMC. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3101 Excessive power on the spindle detected during DMC. Press START to continue CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3102 Non-compatible instruction with active independent movement. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3103 Target power insufficient for the proper operation using DMC. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3104 A collision has been detected. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3105 Tapping or interrupted rigid tapping. Withdrawal allowed in manual mode. Press ENTER + RESET to confirm. CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3106 Wrong gear change procedure. Warning! Master and slave may be in different gears. CNCelite 8058 / 8060 / 8065 / 8070
• 3107 Master and slave tandem are in different gears. CNCelite 8058 / 8060 / 8065 / 8070
• 3400 The independent axis does not exist or is not available CNCelite 8058 / 8060 / 8065 / 8070
• 3400 The independent axis does not exist or is not available CNC 8058 / 8060 / 8065 · CNC 8070
• 3401 The cam does not exist or is not available CNC 8070
• 3401 The cam does not exist or is not available CNCelite 8058 / 8060 / 8065 / 8070
• 3401 The cam does not exist or is not available CNC 8058 / 8060 / 8065
• 3402 No more operations are allowed with independent axes. Table full. CNCelite 8058 / 8060 / 8065 / 8070
• 3402 No more operations are allowed with independent axes. Table full. CNC 8058 / 8060 / 8065 · CNC 8070
• 3403 No more operations are allowed with independent axes. In synchronization CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3404 #FOLLOW OFF not admitted with another operation pending CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3405 #MOVE INF not admitted for an axis with travel limits CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3406 The speed needed to synchronize exceeds the maximum CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3407 The coordinate programmed for the independent axis exceeds the positive travel limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3408 The coordinate programmed for the independent axis is smaller than the negative travel limit CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3409 The axis is not valid as independent axis CNC 8058 / 8060 / 8065 · CNC 8070
• 3410 The maximum amount of time allowed for synchronizing has been exceeded CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
• 3411 An attempt has been made to exceed to the maximum feedrate MAXFEED CNCelite 8058 / 8060 / 8065 / 8070
• 3411 An attempt has been made to exceed to the maximum feedrate MAXFEED CNC 8058 / 8060 / 8065 · CNC 8070