Error codes
Look up an error or alarm code from your Fagor CNC, drive or digital readout and see its cause and solution, with a link to the page in the manual.
All codes (4.787)
- 4004 Overtemperature at the motor (108) CNC 8055 T
- 4004 Parameter G00FEED higher at the CNC than at the drive CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4005 Following error monitoring not active at the drive CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4005 Overtemperature at the heatsink ( 106 ) CNC 8055 M
- 4005 Overtemperature at the heatsink (106) CNC 8055 T
- 4006 Drive parameter SP100 must be 0 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4006 Voltage control error (100...105) CNC 8055 M · CNC 8055 T
- 4007 Feedback error ( 600...606 ) CNC 8055 M
- 4007 Feedback error (600...606) CNC 8055 T
- 4007 The Sercos spindle needs a gain other than 0 CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4008 Error at the power bus ( 213...215 ) CNC 8055 M
- 4008 Error at the power bus (213...215) CNC 8055 T
- 4008 Sercos ring Error+ because the drive has been reset CNC 8058 / 8060 / 8065 · CNC 8070
- 4008 Sercos ring Error+ because the drive has been reset CNCelite 8058 / 8060 / 8065 / 8070
- 4009 Overcurrent ( 212 ) CNC 8055 M
- 4009 Overcurrent (212) CNC 8055 T
- 4009 Too many variables in a Sercos telegram CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4010 Overvoltage at the power bus ( 304/306 ) CNC 8055 M
- 4010 Overvoltage at the power bus (304/306) CNC 8055 T
- 4010 The parameter cannot be written at the drive CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4011 The parameter cannot be written at the drive: No IDN CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4011 Undervoltage at the power bus ( 307 ) CNC 8055 M
- 4011 Undervoltage at the power bus (307) CNC 8055 T
- 4012 Drive error CNC 8055 M · CNC 8055 T
- 4012 The parameter cannot be written at the drive: Out of range CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4013 Position deviation too high CNC 8055 M · CNC 8055 T
- 4013 The parameter cannot be written at the drive: Protected CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4014 Communications error CNC 8055 M · CNC 8055 T
- 4014 Error when initializing the SERCON CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
- 4015 TimeOut when initializing the Sercos ring CNC 8058 / 8060 / 8065 · CNC 8070 · CNCelite 8058 / 8060 / 8065 / 8070
Log in to download
New to the platform?
Create an account
·
